Mica Band Heaters

Type L1 leads

• Leads exiting both sides of gap are standard unless otherwise specified.
• High temperature fiberglass leads are rated to 850°F.
• Standard lead length is 10 inches.
• Minimum Diameter: 3/4 inch
• Minimum Width: 3/4 inch

Type L2 leads

• Leads exit 180° from the gap unless otherwise specified.
• 1.5" of sleeve protection is standard on lead exits.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type L3 leads

• Leads exiting straight out the side are available on any construction.
• Leads exit through a brass eyelet.
• Minimum Diameter: 1.50 inch
• Minimum Width: 3/4 inch

Type L4 leads

• Leads may exit at right angle out of cap from any position on the heater.
• 1.5" of sleeve protection is standard.
• Minimum Diameter: 1.25 inch
• Minimum Width: 1 inch

Type L5 leads

• Lead wires on one side of gap are available on any construction.
• Common exit for small band heaters.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type L6 leads

• Stainless steel spring provides extra support, protecting leads from sharp bends.
• Minimum Diameter: 1.50 inch
• Minimum Width: .75 inch

Type B1 braid

• Stainless Steel braid exiting both sides of gap.
• Leads are 2" longer than S/S braid.
• Stainless steel braid offers both flexibility and abrasion protection.
• Minimum Diameter: 3/4 inch
• Minimum Width: 3/4 inch

Type B2 braid

• Stainless Steel braid exiting 180 degrees from gap.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type B3 braid

• Stainless Steel braid straight out side.
• Leads exit sheath through brass eyelet.
• Minimum Diameter: 1.50 inch
• Minimum Width: 3/4 inch

Type B4 braid

• Stainless Steel braid with right angle exit through cap.
• Minimum Diameter: 1.25 inch
• Minimum Width: 1 inch

Type B5 braid

• Stainless Steel braid out same side of gap.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type B6 braid

• Stainless Steel braid with spring guard.
• Minimum Diameter: 1.50 inch
• Minimum Width: 3/4 inch

Type C3 conduit

• Flexible Stainless Steel Conduit offers utmost lead abrasion protection.
• Leads are 2" longer than conduit.
• Stainless Steel Conduit is sometimes referred to as armor cable or hose.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type C4 conduit

• Flexible Stainless Steel Conduit exiting through right angle cap.
• Minimum Diameter: 1.50 inch
• Minimum Width: 1 inch

Type N1 terminals

• Post Terminal Vertical position.
• This is standard position for heaters 2” wide and greater.
• #10-24 screw thread.
• Minimum Diameter: 1 inch
• Minimum Width: 2.75 inch

Type N2 terminals

• Post Terminals each side of gap.
• This is standard position for nozzle heaters and band heaters less than 2” wide.
• #10-24 screw thread.
• Minimum Diameter: 1 inch 
• Minimum Width: 1 inch

Type N3 terminals

• Post Terminals Parallel position.
• #10-24 screw thread.
• Minimum Diameter: 1 inch
• Minimum Width: 1 inch

Type BN terminals

• Button terminals are useful in low clearance applications.
• Button terminals may be ordered in same position as N-1, N-2 or N-3.